FRT Guide
What an FRT is, which type fits your rifle, the parts it needs to run, how to fix the common problems, and where they're legal.
What is a forced reset trigger?
A forced reset trigger (FRT) is a semi-automatic trigger group that uses the rifle's own cycling to push the trigger forward and reset it after every shot. On a standard trigger, your finger has to let the trigger travel forward until it resets. On an FRT, the bolt carrier does that work for you as it moves back.
It still fires one round per function of the trigger. To fire again, the trigger has to move forward and reset, then be pulled again. Keep rearward pressure on the trigger and let it push your finger forward on each reset, and follow-up shots get much faster than with a standard trigger.
An FRT is not the same as:
- A binary trigger, which fires once on the pull and once on the release.
- A bump stock, which uses recoil to bounce the whole rifle against a stationary finger.
- A machine gun, which keeps firing as long as the trigger is held back.
Types of FRTs
Not sure which way to go? A drop-in cassette with a matched carrier and buffer is the simplest complete setup on a standard AR-15. Our Build Your Own Disruptor Combo puts all three together.
BCG, buffer and gas: what your rifle needs
Bolt carrier group (BCG)
Cassette FRTs use the rear of the bolt carrier to push the trigger back into reset. A full-auto (M16) profile carrier has the extra mass and shape at the rear that does this. A semi-auto profile carrier is cut away there, so the trigger never gets reset and goes dead after the first shot. If your rifle has a semi-auto carrier, swap to an M16-profile BCG before you install a cassette FRT. Selector-style systems vary, so check the product listing.
If you need a carrier, the KAK DBC BCG is built for FRT use.
Buffer weight
The buffer controls how fast the carrier comes back forward. Too light and the carrier can outrun the reset. Good starting points:
| Setup | Starting buffer |
|---|---|
| 16" mid-length gas, unsuppressed | H2 (about 4.6 oz) |
| Under 16", or suppressed | H3 (about 5.0–5.4 oz) |
| 20" rifle-length gas | Rifle buffer or H2 |
| Carbine or mid-length gas, suppressed | H3 with a fresh, stronger spring |
A one-piece option like the Odin Works HFRT system or the adjustable Odin Works heavy buffer lets you tune weight without buying several buffers. See all buffers in AR Parts & Accessories.
Gas
If a heavier buffer makes the rifle short-stroke (it won't lock back on an empty magazine), the rifle is under-gassed for that weight. An adjustable gas block fixes this: open it until the bolt reliably locks back on empty, then give it one more click.
Installation basics
Every FRT ships with the manufacturer's instructions. Follow them for your exact model. In general:
- Unload and clear the rifle. Remove the magazine, lock the bolt back, and visually and physically check the chamber. Keep ammunition out of the room.
- Separate the upper and lower and remove the existing hammer, trigger, disconnector and (if the kit includes one) selector.
- Install the FRT exactly as shown in its instructions. Drop-in cassettes use your existing or supplied pins. Don't file, bend or alter parts unless the manufacturer says fitting is required.
- Install the M16-profile BCG and the correct buffer if your setup needs them.
- Function check before live fire. With the rifle unloaded, confirm the safe position won't fire, the trigger releases the hammer in fire, and the trigger resets when you cycle the charging handle.
- Test at the range with quality full-power ammunition. Light target loads are a common cause of reset problems.
If you aren't comfortable working on your rifle's fire control group, have a qualified gunsmith do the install.
Troubleshooting
| What's happening | Likely cause | What to try |
|---|---|---|
| Trigger is dead after the first shot | Semi-auto profile carrier | Install an M16-profile BCG |
| Fires one or two rounds, then won't reset | Buffer too light; carrier is outrunning the reset | Step up a buffer weight (H2 to H3) and install a fresh spring |
| Light primer strikes, no bang | Carrier bounce | Add buffer weight; check hammer and firing pin springs |
| Won't lock back on empty after adding weight | Under-gassed | Open an adjustable gas block, or drop one buffer step |
| Reset quits when a suppressor goes on | Extra back pressure speeds up the carrier | Go one buffer weight heavier or reduce gas |
| Reset gets worse over time | Worn buffer spring | Replace the buffer spring first |
| Inconsistent reset with cheap ammo | Underpowered loads | Run quality full-power ammunition |
Still stuck? Contact us with your rifle's barrel length, gas system, carrier and buffer, and we'll help you sort it out.
Are FRTs legal?
Federal law
On May 16, 2025, the U.S. Department of Justice announced a settlement ending its lawsuits against Rare Breed Triggers over forced reset triggers. The settlement followed the Supreme Court's 2024 bump stock ruling in Garland v. Cargill and a 2024 federal court decision holding that FRTs are not machine guns under federal law. Under the settlement, the manufacturer agreed not to develop FRTs for pistols. FRTs for rifles are legal to own under federal law.
State and local law
Some states ban or restrict FRTs under their own laws, separate from federal law. As of November 2026, these include:
California, Colorado, Connecticut, Delaware, Hawaii, Illinois, Maryland, Massachusetts, Minnesota, New Jersey, New York, Oregon and Washington, D.C.
In Nevada, Rhode Island and Washington, whether existing laws cover FRTs is disputed. Treat them as restricted unless you've confirmed otherwise.
We don't sell FRTs into restricted areas. Our checkout automatically blocks FRT orders shipping to states and territories where they're restricted.
Ready to build?
Every FRT, combo and super safety we carry is in one place. Questions about fit? Call (270) 681-7657 or email kohl.sales@kgwarms.com
Shop FRTsShop buffers & partsSubscribe to our emails
Be the first to know about new collections and exclusive offers.